Adaptec 1542B - AHA Storage Controller Fast SCSI 10 MBps Przewodnik Instalacji Strona 27
- Strona / 127
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
For example, set the tape drive’s SCSI ID to 7 using jumpers or an external switch.
Then set the AHA-274x SCSI ID to 6 using the ECU. (Use the configuration BIOS
accessed by Ctrl-A at boot to change the setting on the AHA-284x.)
A large disk used with the Solaris operating environment on an AIC-7770
controller cannot be mounted on a controller with a different geometry; the DPT
PM-2022 controller, for example.
Some VESA local bus motherboards do not support more than one bus master
controller, like the AHA-2840VL host bus adapter.
When using AHA-2742T and AHA-2842VL adapters with slow tape devices,
under heavy loads error messages like this are displayed:
Warning: /eisa/esa@2c00/cmtp@4,0 (Tape4):
0.25 inch cartridge
Tape 11: Fixed record length (512 byte blocks) I/O
Set the SCSI ID of the tape drive higher than the host bus adapter.
For example, set the tape SCSI ID to 6 and the host bus adapter SCSI ID to 5 or less
by doing the following:
Log in as root and shut down the Solaris operating environment.
Boot DOS and change the target ID of the host bus adapter to 5 using the ECU
supplied by the motherboard manufacturer.
Turn off the computer and power down the tape.
Jumper the tape device to SCSI ID 6.
Boot the Solaris operating environment and run the drvconfig and tapes
utilities.
Configuration Procedure
1. Select channel A as the Primary Channel.
2. Run the BIOS configuration and verify that BIOS support for more than two
drives is disabled.
3. If there are multiple AIC-7770 controllers on one system, the order of the I/O
base addresses must match the order of the BIOS base addresses.
On an EISA motherboard, the I/O base address corresponds to the EISA slot
number times 0x1000 plus 0xC00 for controller boards. For example, if the first
slot has an AHA-274x controller, the address is 0x1C00, and if the adjacent slot
also has an AHA-274x controller, the address is 0x2C00. Motherboard
manufacturers usually map the controller chip on the motherboard at the highest
Device Reference Pages 15
- Device Reference Manual for 1
- Contents 3
- Contents v 5
- Contents vii 7
- Contents ix 9
- Before You Read This Book 11
- Ordering Sun Documents 12
- Device Reference Pages 13
- Third-Party Drivers 13
- Using Device Reference Pages 14
- Disk Interface 15
- (Including ATAPI CD-ROM) 15
- • IRQ Level: 15 16
- • I/O Address: 0x170 16
- • Drive Type: Not installed 16
- • Enhanced IDE Drive: Enabled 16
- Device Reference Pages 5 17
- SCSI Host Bus Adapters 18
- 1530P, 1532P HBAs 18
- Interface 20
- Device Reference Pages 9 21
- 1542CF, 1542CP HBAs 22
- Device Reference Pages 11 23
- Adaptec AHA-1640, 1642 HBAs 24
- Adaptec AHA-1740, 1742A HBAs 25
- 2742W, 2840VL, 2842VL HBAs 26
- 3940UW, 3940AU, 3940AUW 29
- Device Reference Pages 19 31
- QLogic QLA510 HBAs 32
- BT-445S HBAs 33
- Special Cases 34
- Wide SCSI HBAs 38
- Device Reference Pages 29 41
- PM-3021 HBAs 42
- Device Reference Pages 31 43
- DPT PM-2012B HBA 44
- • Bus: Enabled 45
- • IDE Boot Address: Primary 45
- • Option ROM Address: Default 45
- • SCSI ID HBA: Default 7 45
- IBM Micro Channel HBA 46
- Adapter/A 47
- PCE-5 SCSI) 48
- 53C825A HBAs (DU 1) 49
- Subsystem HBAs 53
- SCSI RAID Controller (DU 2) 54
- 4. Reboot 55
- Compaq SMART Array Controller 56
- Compaq SMART-2, SMART-2SL 57
- SMART-2DH Array Controllers 57
- PM-2142W SCSI and PM-3222 58
- PM-3332UW SCSI RAID HBAs 58
- PM-2124, PM-2124W, PM-2144W 60
- PM-2144UW SCSI and PM-3224 60
- PM-3224W, PM-3334W, PM-3334UW 60
- SCSI RAID HBAs 60
- Supported Settings 61
- IBM PC ServeRAID SCSI HBA 62
- Graphics Cards 65
- Intergraph G91 65
- Device Reference Pages 55 67
- Ethernet Network Adapters 68
- 3Com EtherLink 16 (3C507) 68
- II/16 (3C503-16) 69
- Device Reference Pages 61 73
- NetFlex-2 ENET-TR Controllers 74
- Device Reference Pages 63 75
- Compaq NetFlex-3, Netelligent 76
- Controllers 76
- # touch /reconfigure 78
- # reboot 78
- Ethernet (DU 3) 79
- Device Reference Pages 69 81
- MCA TP (82586) 83
- Device Reference Pages 77 89
- Novell NE3200 Ethernet 90
- Ethernet 91
- SMC Elite32 (8033) 93
- SMC Elite32C Ultra (8232) 94
- SMC Ether 10/100 (9232) 95
- 32T (8033) 96
- 0x260 5 0xE0000 97
- 0x380 7 0xD4000 97
- Token Ring Network Adapters 100
- Ring and Compatible Adapters 100
- Configuration Procedure 101
- Preconfiguration Information 103
- Audio Cards 105
- Analog Devices AD1848 and 105
- Compatible Devices 105
- Device Reference Pages 95 107
- Blaster Pro-2 109
- • IRQ Level: 2, 5, 7,10 110
- • I/O Address: 110
- 0x220, 0x240 110
- • DMA Channel: 0, 1,3 110
- PC Card (PCMCIA) Hardware 113
- PC Card Adapters 113
- Device Reference Pages 103 115
- Configuring Two or More Cards 117
- Special Files 118
- Hot-Plugging 118
- Additional Configuration 121
- SRAM and DRAM PC Card Devices 122
- Using PC Card Memory Devices 124
- PC Card ATA Devices 125
- # newfs /dev/rdsk/c#d#s# 127
Powiązane produkty i podręczniki dla Oprogramowanie Adaptec 1542B - AHA Storage Controller Fast SCSI 10 MBps
(9 strony)
(2 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji