Adaptec ASH-1233 Podręcznik Użytkownika Strona 1

RAdaptec ASH-1233ATA AdapterUser’s Guide

3Installation ChecklistInstallation ChecklistTo successfully install your Adaptec ASH-1233 adapter and ATA disk drives, perform these tasks, in order:

4Installing Your Adaptec ASH-1233 Adapter3 Locate an unused expansion slot and remove the slot cover. Save the slot cover screw for use in Step 5.4Ins

5Preparing Your ATA Disk DrivesPreparing Your ATA Disk DrivesBecause setup can vary from device to device or computer to computer, always refer to you

6Connecting Your ATA Disk DrivesConnecting Your ATA Disk DrivesThe ASH-1233 adapter supports up to four ATA disk drives in a master/slave configuratio

7Connecting Your ATA Disk DrivesConnecting One ATA Disk Drive on a CableWhen you connect only one ATA disk drive to a cable, that disk drive must be s

8Mounting ATA Disk Drives and Connecting Power CablesConnecting Two ATA Disk Drives to the Same CableWhen you connect two ATA disk drives to a cable,

9Installing the Device Driver2 Connect an LED cable from your computer’s motherboard to the primary LED connector on your ASH-1233 adapter (shown in t

10Installing the Device DriverWindows XPWhen you power on your computer, Windows automatically detects the new adapter and opens the New Hardware Inst

11Installing the Device Driver5 To verify that the adapter is installed correctly, right-click the My Computer desktop icon, select Properties, click

12Installing the Device DriverWindows 2000When you power on your computer, Windows automatically detects the new adapter and opens the New Hardware In

iCopyright© 2004 Adaptec, Inc. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any

13Installing the Device Driver4 Select CD-ROM drives, then click Next.5 Click Next again.6 When the installation is complete, click Finish.7 Restart y

14Installing the Device Driver8 To verify that the adapter is installed correctly, right-click the My Computer desktop icon, select Properties, click

15Installing the Device DriverWindows MeWhen you power on your computer, Windows automatically detects the new adapter and opens the New Hardware Inst

16Installing the Device Driver4 To verify that the adapter is installed correctly, right-click the My Computer desktop icon, select Properties, then c

17Installing the Device DriverWindows 98SENote: You may need your Windows 98SE CD during installation.When you power on your computer, Windows automat

18Installing the Device Driver4 Select CD-ROM drive, then click Next.5 Click Next again.6 When the installation is complete, click Finish.

19Registering Your Adaptec ASH-1233 Adapter7 To verify that the adapter is installed correctly, right-click the My Computer desktop icon, select Prope

20TroubleshootingTroubleshootingIf you have any problems using the Adaptec ASH-1233 adapter, work through these troubleshooting suggestions: Ensure t

RAdaptec, Inc.691 South Milpitas BoulevardMilpitas, CA 95035 USA©2004 Adaptec, Inc.All rights reserved. Adaptec and the Adaptec logo are trademarks of

iiAdaptec Customer SupportIf you have questions about installing or using your Adaptec product, check this document first—you will find answers to mos

iiiLimited 5-Year Hardware Warranty1. Adaptec, Inc. (“Adaptec”) warrants to the purchaser of this product that it will be free from defects in materia

ivSoftware License AgreementPLEASE READ CAREFULLY: THE USE OF THIS SOFTWARE IS SUBJECT TO THE SOFTWARE LICENSE TERMS OF ADAPTEC, INC. AND OTHER LICENS

v7. Limited Warranty. Adaptec and its Licensor warrant only that the media upon which the Software is furnished will be free from defects in material

viRegulatory Compliance StatementsFederal Communications Commission Radio Frequency Interference StatementWARNING: Changes or modifications to this un

1In this GuideThe Adaptec ASH-1233 ATA adapter provides increased performance with enhanced ATA technology. The Adaptec ASH-1233 supports ATA/133 hard

2System RequirementsSystem RequirementsThe minimum system requirements for the ASH-1233 adapter are: Pentium II-266 MHz Processor or higher Microsof